Sculptor's render of the painted design (kit ships unpainted): front view of the mushroom-capped traveler with a lit lantern beside the frog fishing from a log, above the stone-rimmed pond

Chibi Mushroom-Capped Traveler Resin Garage Kit – Lantern, Fishing Frog on a Log & Stone-Rimmed Pond Base (Unpainted, 15 Pieces)

Full kit, 15 pieces
$54.00
Skip to product information
Sculptor's render of the painted design (kit ships unpainted): front view of the mushroom-capped traveler with a lit lantern beside the frog fishing from a log, above the stone-rimmed pond
  • Sculptor's render of the painted design (kit ships unpainted): front view of the mushroom-capped traveler with a lit lantern beside the frog fishing from a log, above the stone-rimmed pond
  • Sculptor's render (kit ships unpainted): view from the left showing the spotted top of the cap, the flag pole and the standing stone
  • Sculptor's render (kit ships unpainted): rear view of the canvas pack, bedroll and two saddle bags under the mushroom cap
  • Sculptor's render (kit ships unpainted): rear view from the right with the chained crates, the trunk and the frog's satchel
  • Sculptor's render (kit ships unpainted): closer view of the lit lantern and the frog on its log with the fishing rod
  • Sculptor's render (kit ships unpainted): both figures from the front, the crates and chains behind them
  • Sculptor's render (kit ships unpainted): close-up of the traveler's face with the moss fringe and shawl bow
  • Sculptor's render (kit ships unpainted): close-up of the frog's face, eyes closed and mouth open, holding the rod
  • Sculptor's render (kit ships unpainted): unpainted gray view of the whole scene from the front
  • Sculptor's render (kit ships unpainted): unpainted gray view from behind showing the pack, saddle bag and chained cargo
  • Sculptor's render of the painted design (kit ships unpainted): front view of the mushroom-capped traveler with a lit lantern beside the frog fishing from a log, above the stone-rimmed pond
  • Sculptor's render (kit ships unpainted): view from the left showing the spotted top of the cap, the flag pole and the standing stone
  • Sculptor's render (kit ships unpainted): rear view of the canvas pack, bedroll and two saddle bags under the mushroom cap
  • Sculptor's render (kit ships unpainted): rear view from the right with the chained crates, the trunk and the frog's satchel
  • Sculptor's render (kit ships unpainted): closer view of the lit lantern and the frog on its log with the fishing rod
  • Sculptor's render (kit ships unpainted): both figures from the front, the crates and chains behind them
  • Sculptor's render (kit ships unpainted): close-up of the traveler's face with the moss fringe and shawl bow
  • Sculptor's render (kit ships unpainted): close-up of the frog's face, eyes closed and mouth open, holding the rod
  • Sculptor's render (kit ships unpainted): unpainted gray view of the whole scene from the front
  • Sculptor's render (kit ships unpainted): unpainted gray view from behind showing the pack, saddle bag and chained cargo
Chibi Mushroom-Capped Traveler Resin Garage Kit – Lantern, Fishing Frog on a Log & Stone-Rimmed Pond Base (Unpainted, 15 Pieces)

Chibi Mushroom-Capped Traveler Resin Garage Kit – Lantern, Fishing Frog on a Log & Stone-Rimmed Pond Base (Unpainted, 15 Pieces)

$54.00
KitFull kit, 15 pieces

Printed to order. This listing shows as sold out until the next print run is ready. Tap Notify me and leave your email, and I'll let you know when it's in stock. No pre-orders and nothing to pay up front. How it works

IMPORTANT: THIS IS AN UNPAINTED, UNASSEMBLED RAW RESIN KIT. IT IS NOT A FINISHED FIGURE.

The pictures are the sculptor's digital renders of the painted design. Your kit arrives as 15 separate pieces of plain, single-color resin. It is:

  • Unassembled: you glue the pieces together yourself.
  • Unprimed: it needs primer before paint.
  • Unsanded: seams and surfaces need sanding.
  • Unpainted: all painting is up to you.

Expect supports and support marks. Some parts may ship with supports still attached to make sure they do not get damaged during shipping. You may need to sand parts to fully remove supports or fill marks where supports attached. You will need to prime with an appropriate primer.

This kit is for people who want the full experience of finishing a 3D printed kit without owning a printer. It’s also a good way to find out whether the hobby is for you, and what finishing a printed model really takes, before you buy a printer of your own.

An original chibi scene, the studio's own design. A round, cream-colored little creature in a wide mushroom cap stands at the edge of a pond, holding a lit lantern low in one hand and raising the other toward its friend. The cap is rust red with raised pale spots and a scalloped rim over a fringe of moss, and the creature wears a tan shawl tied in a bow at the chest. On its back is a traveler's load: a canvas pack with buckled straps, a rolled bedroll and a two-pocket leather saddle bag at each side. Beside it, a smiling frog in a hooded cloak sits on a cut log, eyes closed and mouth wide open, holding a fishing rod whose line drops to a red float in the water. The base is a grassy mound with flowering bushes, a tall standing stone, a ring of cut stone blocks around a dark pond with lily pads and a lotus bud, a stack of chained crates and a padlocked trunk on a pallet, and a branch pole flying a tattered flag.

What's in the kit

  • 15 resin pieces in total.
  • Traveler, 4 pieces: the head with its moss fringe, the body with the shawl and the raised hand, the arm holding the lantern, and the mushroom cap.
  • Pack, 3 pieces: the canvas pack with its straps and bedroll, and the two saddle bags.
  • Frog, 3 pieces: the head, the seated body in its cloak, and the fishing rod with its line and float as a single piece.
  • Base, 5 pieces: the grass-and-pond base, the log, the crate-and-trunk stack, the flag pole and the flag.
  • Studio size: 80 mm (3.15 in) tall, 76 × 95 mm (2.99 × 3.74 in) footprint (from the studio's scale sheet).

About the sizes: every measurement above comes from the sculptor's own files or the studio's published size information for the unprinted model. Your printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

Skill level: intermediate

  • The fishing rod, line and float are one thin piece that has to sit in both of the frog's hands with the float on its ripple in the pond. Fit it last and hold it until the glue grabs.
  • The two saddle bags, the flag and the flag pole have no pegs. Dry-fit the bags against the pack, then glue and hold each one.
  • The cap, the head, the frog's body and the crate stack key in with square pegs. The cap's seam hides in the moss.
  • Thin parts: the lantern cage, the fishing rod and the frayed edge of the flag.

You'll need (not included): sandpaper or sanding sticks, flush cutters, CA glue or epoxy, primer, paints, and brass rod if you pin the joints.

How ordering works

Every kit is printed to order in small runs, based on waitlist demand. This listing shows as out of stock until the next run is ready. Tap Notify me and leave your email, and I'll let you know when it's in stock. There are no pre-orders. You're never charged for a kit that hasn't been printed.

Shipping and returns

  • Free shipping to addresses in the 50 US states, Washington, DC, and military APO/FPO addresses.
  • International or US territory address? You can use a US package forwarding service. My responsibility ends when the package is delivered to the forwarder’s US address. Anything after that is between you and the forwarding service.
  • 30-day free returns. If the kit isn't for you, send it back within 30 days of delivery, unassembled and unsanded, and I'll send you a prepaid return label.

Sculptor credit and license

This sculpt is by NomNom Figures. I print it from the sculptor's original files and sell it under the commercial license that comes with my membership in NomNom Figures' commercial tier on Patreon. Please support the artist:

This is the sculptor's own original character. The design belongs to the sculptor; I sell physical prints of it under the license described above.

You may also like