Sculptor's render of the painted design (kit ships unpainted): front view of the whole figure rising from three columns of cream and tan smoke, with the white paper-sheet wings spread around her

Chibi Paper-Winged Woman Resin Garage Kit – Paper Sheet Wings, Paper Rose & Three-Column Smoke Base (Unpainted, 13 Pieces)

Full kit, 13 pieces
$97.00
Skip to product information
Sculptor's render of the painted design (kit ships unpainted): front view of the whole figure rising from three columns of cream and tan smoke, with the white paper-sheet wings spread around her
  • Sculptor's render of the painted design (kit ships unpainted): front view of the whole figure rising from three columns of cream and tan smoke, with the white paper-sheet wings spread around her
  • Sculptor's render (kit ships unpainted): close view from the hem up, showing the face with amber eyes, the paper rose on her bun, the red-lined bell sleeves and the paper-square hem
  • Sculptor's render of the painted design (kit ships unpainted): front view of the whole figure rising from three columns of cream and tan smoke, with the white paper-sheet wings spread around her
  • Sculptor's render (kit ships unpainted): close view from the hem up, showing the face with amber eyes, the paper rose on her bun, the red-lined bell sleeves and the paper-square hem
Chibi Paper-Winged Woman Resin Garage Kit – Paper Sheet Wings, Paper Rose & Three-Column Smoke Base (Unpainted, 13 Pieces)

Chibi Paper-Winged Woman Resin Garage Kit – Paper Sheet Wings, Paper Rose & Three-Column Smoke Base (Unpainted, 13 Pieces)

$97.00
KitFull kit, 13 pieces

Printed to order. This listing shows as sold out until the next print run is ready. Tap Notify me and leave your email, and I'll let you know when it's in stock. No pre-orders and nothing to pay up front. How it works

IMPORTANT: THIS IS AN UNPAINTED, UNASSEMBLED RAW RESIN KIT. IT IS NOT A FINISHED FIGURE.

The pictures are the sculptor's digital renders of the painted design. Your kit arrives as 13 separate pieces of plain, single-color resin. It is:

  • Unassembled: you glue the pieces together yourself.
  • Unprimed: it needs primer before paint.
  • Unsanded: seams and surfaces need sanding.
  • Unpainted: all painting is up to you.

Expect supports and support marks. Some parts may ship with supports still attached to make sure they do not get damaged during shipping. You may need to sand parts to fully remove supports or fill marks where supports attached. You will need to prime with an appropriate primer.

This kit is for people who want the full experience of finishing a 3D printed kit without owning a printer. It’s also a good way to find out whether the hobby is for you, and what finishing a printed model really takes, before you buy a printer of your own.

A fan-art chibi of the calm, paper-wielding woman from a long-running ninja anime, rising out of three columns of smoke. She floats upright with her arms low and a little out from her sides, palms open and turned forward. Two tall wings built from hundreds of small square paper sheets rise from behind her shoulders and curve forward around her. She has a chin-length blue-violet bob with a side-swept fringe, a small bun on top with a white paper rose pinned beside it, amber eyes under dark liner and lilac eyeshadow, a soft blush and a small stud below her lip. She wears a high-collared black cloak with a red trim line down the front, red cloud emblems on the chest and hips, and wide bell sleeves with deep red lining. Below the hips the cloak breaks apart into layered black and white paper squares that sit on the center smoke column. The base is billowing cream-to-peach smoke in three columns over low cloud masses, with loose paper sheets caught in it.

What's in the kit

  • 13 resin pieces in total.
  • Figure, 8 pieces: the head, the front hair, the cloak torso with its paper-square hem, two bell sleeves, two hands and the paper rose.
  • Wings, 2 pieces: the left and right paper-sheet wings.
  • Base, 3 pieces: the three-column smoke base cut in three sections.
  • Tallest single piece: the right wing, 173.3 mm (6.82 in) in the sculptor's file. The sculptor doesn't publish an assembled height or scale, so I don't list one.
  • Smoke base: 200.2 × 174.1 mm (7.88 × 6.85 in) across, from the sculptor's single-piece file of the same base.

About the sizes: every measurement above comes from the sculptor's own files or the studio's published size information for the unprinted model. Your printed kit can differ slightly: resin shrinks a little as it cures, removing supports and sanding takes off some material, and the assembled height depends on how the parts are fitted. Treat the numbers as a close guide, not an exact guarantee.

Skill level: advanced

  • Each wing is a large piece over 170 mm tall, built from hundreds of thin paper-sheet edges, and it hangs off the back of the torso. Pin both wings.
  • The whole figure rests on the top of the center smoke column at her hem. Pin that join, and dry-fit the wings and base together before gluing, since the lower wing tips reach toward the outer columns.
  • The three base sections have to line up level under the figure. Fill the two seams through the smoke.
  • The hands, the paper rose and the hair strands are small and thin.

You'll need (not included): sandpaper or sanding sticks, flush cutters, CA glue or epoxy, primer, paints, and brass rod if you pin the joints.

How ordering works

Every kit is printed to order in small runs, based on waitlist demand. This listing shows as out of stock until the next run is ready. Tap Notify me and leave your email, and I'll let you know when it's in stock. There are no pre-orders. You're never charged for a kit that hasn't been printed.

Shipping and returns

  • Free shipping to addresses in the 50 US states, Washington, DC, and military APO/FPO addresses.
  • International or US territory address? You can use a US package forwarding service. My responsibility ends when the package is delivered to the forwarder’s US address. Anything after that is between you and the forwarding service.
  • 30-day free returns. If the kit isn't for you, send it back within 30 days of delivery, unassembled and unsanded, and I'll send you a prepaid return label.

Sculptor credit and license

This sculpt is by Chibi Station. I print it from the sculptor's original files and sell it under the commercial license that comes with my membership in Chibi Station's commercial tier on Patreon. Please support the artist:

Fan art notice: this is an unofficial, fan-made sculpture. I don't own, and claim no rights to, the character or the source material it's based on. All rights to them belong to their respective owners, who have not endorsed and are not affiliated with this product.

You may also like